sludge dryer
Sludge Dryeris mainly used in the fields of building materials, mineral processing, metallurgy, chemical industry, etc., Oursewage sludge dryer can be used to dry materials with specified moisture and size. Working principle ofSewage Sludge Dryer Se
Sludge Dryer is mainly used in the fields of building materials, mineral processing, metallurgy, chemical industry, etc., Our sewage sludge dryer can be used to dry materials with specified moisture and size.
Working principle of Sewage Sludge Dryer
Sewage Sludge Dryer is consist of heating device, feeding device, transport device, discharge device, dust extraction device and other connecting parts. For the installation process, the Sewage Sludge Dryer should slopes slightly so that the discharge end of Sewage Sludge Dryer is lower than the material feed end in order to convey the material through the Sewage Sludge Dryer under gravity. Material to be dried enters the Sewage Sludge Dryer, and as the Sewage Sludge Dryer rotates, the material is lifted up by a series of internal fins lining the inner wall of the Sewage Sludge Dryer. When the material gets high enough to roll back off the fins, it falls back down to the bottom of Sewage Sludge Dryer, passing through the hot gas stream as it falls.
The Sewage Sludge Dryer is mainly for drying the small size raw material less than 30mm, the moisture content less than 75%.
Firstly, The Sewage Sludge enters into the drying sysem by conveyor or bucket conveyor, the sewage sludge raised by lifting plate to make the sewage sludge and heat totally contact with each other.
The sewage sludge are evenly distributed in Sewage Sludge Dryer cylinder, at the start of the Sewage Sludge Dryer and the end of the Sewage Sludge Dryer have temperature detector, so that you can check everywhere temperature inside the Sewage Sludge Dryer.
After the Sewage Sludge Dryer have fan, it will absorb the hot air into the dryer and finally make the material to dry.
Between the Sewage Sludge Dryer and fan have cyclone, it can collect the dust from the Sewage Sludge Dryer machine.
Features of Sewage Sludge Dryer
1. Wide applicability, available for many kinds of materials;
2. Simple operation, stable performance;
3. Low investment, high efficient and capacity;
4. Low cost in maintenance;
5. The Sewage Sludge Dryer has high degree of mechanization, large production capacity and continuous working;
6. With simple and excellent structure, the material running smoothly inside the Sewage Sludge Dryer cylinder;
7. The Sewage Sludge Dryer with less mechanical failure, low maintenance and low power consumption;
8. The Sewage Sludge Dryer works uniformly and the drying product is very good;
9. With complete dust removal equipment and protect the environmental;
10. The Sewage Sludge Dryer with no dust spilling;
11. Easy to operate and have a good operating environment.
Application
The rotary dryer for copper sludge dryer is widely used for drying the Ore,Gypsum,Vinasse,chalk slags, coal powder, slags, clay and other materials in the building materials, metallurgy, chemical industry, cement industry. you can use coal, gas, electricity, oil and wind power to heat the dryer machine.
sludge dryer Structure
The rotary dryer for copper sludge dryer is mainly composed by the revolving body, lifting plate, driving device, supporting device, sealing ring and other components. So it has the advantages of reasonable structure, perfect in workmanship, high yield, low energy consumption, convenient to operate.
|
model
(mm)
|
Lean degree(%)
|
Rotate speed(r/min)
|
Inlet air temperature
(°C)
|
power
(Kw)
|
capacity
(m3)
|
production(t/h)
|
weight(t)
|
|
Φ600×6000
|
3-5
|
3-8
|
≤700
|
3
|
1.69
|
0.5-1.5
|
2.9
|
|
Φ800×8000
|
3-5
|
3-8
|
≤700
|
4
|
4.01
|
0.8-2.0
|
3.5
|
|
Φ800×10000
|
3-5
|
3-8
|
≤700
|
4
|
5.02
|
0.8-2.5
|
4.5
|
|
Φ1000×10000
|
3-5
|
3-8
|
≤700
|
5.5
|
7.85
|
1.0-3.5
|
5.6
|
|
Φ1200×10000
|
3-5
|
3-8
|
≤700
|
7.5
|
11.30
|
1.8-5
|
14.5
|
|
Φ1200×12000
|
3-5
|
3-8
|
≤700
|
11
|
13.56
|
2-6
|
14.8
|
|
Φ1500×12000
|
3-5
|
2-6
|
≤800
|
15
|
21.19
|
3.5-9
|
17.8
|
|
Φ1800×12000
|
3-5
|
2-6
|
≤800
|
18
|
30.52
|
5-12
|
25
|
|
Φ2200×12000
|
3-5
|
1.5-6
|
≤800
|
18.5
|
45.59
|
6-15
|
33
|
|
Φ2200×18000
|
3-5
|
1.5-6
|
≤800
|
22
|
68.38
|
10-18
|
53.8
|
|
Φ2200×20000
|
3-5
|
1.5-6
|
≤800
|
30
|
75.98
|
12-20
|
56
|
|
Φ2400×20000
|
3-5
|
1.5-5
|
≤800
|
37
|
90.43
|
18-30
|
60
|
|
Φ3000×20000
|
3-5
|
1.5-5
|
≤800
|
55
|
141.3
|
25-35
|
78
|
|
Φ3000×25000
|
3-5
|
1.5-5
|
≤800
|
75
|
176.6
|
32-40
|
104.9
|
