sand making machine
sand making machineis of high-power and low-consumption, which is designed depending on several years hard work and study of mechanical mining equipment. Our sand maker absorbed the advanced technology of the same products of Barmac Company of Americ
sand making machine is of high-power and low-consumption, which is designed depending on several years hard work and study of mechanical mining equipment. Our sand maker absorbed the advanced technology of the same products of Barmac Company of America, now is of the international level.
chromite sand making machine plays an important role in crushing minerals into piecesand it's widely used in all kinds of mineral, cement, corhart, bauxite chmotte, carborundum grain, glass raw material, machine made construction sand, stone stock and all kinds of metallurgy slag, especially carborundum, sintered bauxite, magnesite, and so on material with features of very hard and anticorrosion. And Sand Making Machine is more productive than other kind of crushers.
It has the following features:
1. Rotor with deep chamber increases 30% capacity after perfect design.
2. Side plate direction can be changed to increase material utility ratio, operating ratio can be increased 48%.
3. Worn hammer with combined type is only changed to reduce operating cost 30%. Another pair of vice hammer is
added to prevent from damaging main hammer and side plate.
4. The most key wear resistant material uses wear resistant and high temperature resistant material.
5. Rhombus shape impact plate is used to prevent side plate from being damaged.
6. Bearing is famous international brand imported from Japan, Sweden, America, etc.
7. Perfect discharge and smooth curve reduce resisting force when material flows, so capacity is increased greatly.
8. Spread dish with double purposes can make two feeding ways change easily.
9. Special seal structure under main shaft guarantee no oil leak without seal.
10. Motor with high grade of protection is selected. The motor has features of high efficiency, low noise, etc.
Working principle:
Stone less than 150mm enters sand making machine though conveyor belt. Stone is crushed by hitting other stones. Material falls down to impellor or cavity. Under great centrifugal force, it hits material that coming downwards. After hitting each other, they force a vortex between impellor and shell, and hit each other several times; finally smaller stone comes out, and goes to vibrating screen. Satisfactory material is transported to sand washing machine; however overlarge material will go back to sand maker to be crushed again. Output sizes can be made according to customers requirement. If input size is larger than the designed size, other crushing equipment will be necessary.
|
PXJ fine crusher
|
Rotor width ø×(mm)
|
Rotor widthø×(mm)
|
Rotor width ø×(mm)
|
Rotor width ø×(mm)
|
Rotor width ø×(mm)
|
Rotor width ø×(mm)
|
Rotor width ø×(mm)
|
|
specification
|
800×400
|
800×800
|
1000×1000
|
1200×1200
|
1400×1400
|
1600×1600
|
1800×1800
|
|
Inlet size(mm)
|
400×185
|
550×330
|
1000×350
|
1200×450
|
1500×500
|
1600×550
|
1800×800
|
|
Feeding material size(mm)
|
<120
|
<180
|
<180
|
<180
|
<190
|
<190
|
<190
|
|
Discharging material size(mm)
|
<0.3-5
|
<0.3-5
|
<0.3-5
|
<0.3-5
|
<0.3-5
|
<0.3-5
|
<0.3-5
|
|
Discharging gap adjusting width
|
5-20
|
5-20
|
5-20
|
5-20
|
5-20
|
5-20
|
5-20
|
|
Cement clinker
(T/H)
|
20-30
|
35-45
|
45-55
|
100-110
|
100-150
|
170-210
|
250-270
|
|
limestone(T/H)
|
35-45
|
55-65
|
65-75
|
90-100
|
100-150
|
190-250
|
280-310
|
|
Equipped power(KW)
|
37-45
|
45-55
|
55-75
|
100-132
|
160
|
250
|
315
|
